BANNER PHOTOELECTRIC SENSOR QS30 SERIES

BANNER PHOTOELECTRIC SENSOR QS30 SERIES

Add to Wishlist
Add to Wishlist

BANNER PHOTOELECTRIC SENSOR QS30 SERIES FEATURES:

  • Innovative 30 mm housing design to suit almost any mounting requirement.
  • High-power sensing with ranges up to 200 m.
  • Available in opposed, high-power opposed, polarized and non-polarized retroreflective, diffuse, laser, fixed-field and adjustable-field and clear object sensing modes.
  • Class 1 visible laser in diffuse and retroreflective models and Class 2 in diffuse models.
  • Models with standard 10 to 30V dc supply voltage and bipolar NPN/PNP outputs or 24 to 250V ac/12 to 250V ac supply voltage with e/m relay output.
  • Light- or dark-operate selectable or configurable, depending on model.
  • IP67 or IP69K environmental rating, depending on model.
  • Bright LED operating status indicators visible from 360°.
Category:
Tags:

Description

BANNER PHOTOELECTRIC SENSOR QS30 SERIES

High-Performance Long-Range Sensor

Description:

BANNER PHOTOELECTRIC SENSOR QS30 SERIES

•Reliable detection of clear, translucent, or opaque targets — including mirror-like surfaces.
•Automatic compensation algorithm compensates for dust or contamination on the sensor or reflector and for ambient temperature changes.
•Three selectable thresholds based on type of target being detected •Easy configuration via push buttons or remote wire.
•Easy-to-read operating status indicators.
•Rugged housing for harsh environments; rated IP67 (NEMA 6), 1200 psi washdown per NEMA PW12.
•Compact housing, mounting versatility — 30 mm threaded barrel or side-moun.

BANNER PHOTOELECTRIC SENSOR QS30 SERIES

Specifications-

Supply Voltage

10 V DC to 30 V DC (10% maximum ripple) at 25 mA maximum current,exclusive of load.

Supply Protection Circuitry

Protected against reverse polarity, overvoltage, and transient voltages.

Output Protection

Protected against output short-circuit, continuous overload, transient overvoltages, and false pulse on power up.

Delay at Power-Up

250 ms; outputs do not conduct during this time.

Sensing Beam

660 nm visible red LED.

Sensing Range and Use

100 mm to 2 m (3.9″ to 78″); Light SET for clear object detection.

Indicators

Green LED: Power ON and feedback on configuration and remote wire pulses.

Amber LED: Output conducting or error condition (flashing).

Three-Segment Red Signal Bargraph: Signal strength (excess gain), relative to switchpoint.

Five-Segment Amber Display: Sensor Configuration.

Adjustments

Two push buttons and remote wire.

Easy push-button configuration and deterministic remote wire configuration Select from 3 standard thresholds based on object being detected.

Light Operate/Dark Operate configuration options selectable via push buttons or remote wire.

Push-button lockout (from remote wire only).

Construction

ABS plastic housing; acrylic lens cover.

Output Ratings

150 mA maximum load; see Application Note 1.

OFF-state leakage current: < 50 μA at 30 V DC.

ON-state saturation voltage:

  • NPN: < 200 mV at 10 mA; < 1 V at 150 mA.
  • PNP: < 1.25V at 10 mA; < 2 V at 150 mA.

Output Response Time

500 microseconds.

Repeatability

150 microseconds.

Environmental Rating

Leakproof design rated IEC IP67 (NEMA 6); PW12 1200 PSI washdown.

Connections

5-wire 2 m (6.5 ft) PVC cable, 5-wire 9 m (30 ft) PVC cable, 150 mm (6 in) cable with a 5-pin M12 quick disconnect connector, 150 mm (6 in) PUR cable with 5-pin M12 quick disconnect connector, or a 5-pin integral M12 quickdisconnect connector, depending on the model ordered

Operating Conditions

–10 °C to +55 °C (+14 °F to +131 °F)

95% at +50 °C maximum relative humidity (non-condensing)

Vibration and Mechanical Shock

All models meet MIL-STD-202F, Method 201A (Vibration: 10 Hz to 60 Hz maximum, 0.06 inch (1.52 mm) double amplitude, 10G maximum acceleration) requirements. Also meets IEC 60947-5-2 (Shock: 30G 11 ms duration, half sine wave) requirements.

Application Notes

If the supply voltage is > 24 V DC, derate maximum output current 1 mA/°C above 25 °C.