Need help? Call us: 01326 708334, 01326 708335 or info@voltecbd.com
- Functional principle: Diffuse reflective
- Sensing range: 1 to 30 mm
- Connection type: M8 4-pin plug
- Output Type: NPN
- Operation mode: Light ON
For Price Call: 01329727092
Email: sales@voltecbd.com
- Functional principle: Through-beam
- Sensing range: 500 mm
- Connection type: M8 4-pin plug
- Output Type: PNP
- Operation mode: Light ON
For Price Call: 01329727092
Email: sales@voltecbd.com
- Sensing range (max.): 25 mm
- Connection type: M12 connector
- Switching frequency: 100 Hz
- Installation type: Non Flush
For Price Call: 01329727092
Email: sales@voltecbd.com
- Operation distance_OFF→ON: ± 10 mm
- Operation distance_ON→OFF: ± 20 mm
- Output function: NO
- Operating frequency: 500 Hz
- Switching voltage: ≤ 24VDC
For Price Call: 01329727092
Email: sales@voltecbd.com
- Sensing range (max.): 12 mm
- Connection type: Cable type
- Switching frequency: 50 Hz
- Installation type: Flush
For Price Call: 01329727092
Email: sales@voltecbd.com
- Sensing range (max.): 8 mm
- Switching Output: PNP
- Output function: NO
- Switching frequency: 50 Hz
For Price Call: 01329727092
Email: sales@voltecbd.com
- Sensing range (max.): 15 mm
- Connection type: M12 Connector cable
- Output function: NC
- Switching frequency: 20 Hz
- Installation type: Non Flush
For Price Call: 01329727092
Email: sales@voltecbd.com
- Sensing range (max.): 12 mm
- Connection type: M12 plug connector
- Switching output: PNP
- Output function: NO
- Switching frequency: 10 Hz
- Installation type: Flush
For Price Call: 01329727092
Email: sales@voltecbd.com
- Applicable fluid : (Pneumatic type) Air, Non-corrosive gas
- Pressure port direction : Rear fitting
- Pressure port : Rc1/8
- Connection type : Connector type(connector type cable: 2m)
- Pressure type : Standard pressure
- Power voltage : 12-24VDC
±10%(ripple P-P: max. 10%)
- Current consumption : Voltage output type: Max. 50mA Current output type: Max. 75mA
- Protection structure : IP40
For Price Call: 01329727092
Email: sales@voltecbd.com
- Sensing type : Through-beam type
- Sensing distance : 30m
- Sensing target : Opaque material of min. Ø15mm
- Light source : Red LED(660nm)
- Response time : Max. 1ms
- Measured materials : Liquid, gas, oil
- Measurement pressure : Gauge pressure
- Pressure range : 0 to 10kgf/cm²
- A unique earth ground tester that performs fast, accurate testing with and without stakes
- Tests 3- and 4-pole fall-of-potential, and 4-pole soil resistivity (with stakes)
- Performs selective earth ground rod testing (one clamp + stakes)
- Performs stakeless earth ground rod testing (two clamps)
- Features IP56 rating for outdoor use
By spotting water in drip pans in air handler units, beneath raised floors in data centers, or on floors near sump pumps and drains, the Series WD3 Water Leak Detectors guard equipment against water damage. Once the water has risen to a point where it spans the two conductive strips on the housing's bottom, it is detected. Depending on the model selected, local notice of the alarm situation is provided by audio and visual alerts, and remote indication or control is provided by an internal switch to stop additional water buildup. The Model WD3-BP-D1-A is battery-powered for use in situations where power is not available. Alternatively, the water detector can be powered by either AC or DC supply voltages. By using the provided adjustable mounting bracket, the sensing height can be reduced to as little as 1/32". The mounting bracket can be fastened to any flat surface using either the mounting screws or the connected adhesive strips.
Read more
TCN4S-24R
- Display method : 4-digit 7-segment LED
- Control method : ON/OFF, P, PI, PD, PID
- Input specification : Thermocouple: K(CA), J(IC), T(CC), R(PR), S(PR), L(IC) RTD: DPt100Ω, Cu50Ω
- Sampling cycle : 100ms
- Control output : Relay(250VAC~ 3A) or SSR drive(12VDC ) [ON/OFF]
- Power supply : 100-240VAC~ 50/60Hz
- Display method : 4-digit 7-segment LED.
- Control method : ON/OFF, P, PI, PD, PID.
- Input specification : Thermocouple: K(CA), J(IC), E(CR), T(CC), B(PR), R(PR), S(PR), N(NN), C(TT), G(TT), L(IC), U(CC), Platinel II. RTD: DPt100Ω, DPt50Ω, JPt100Ω, Cu100Ω, Cu50Ω, Nikel 120Ω. Analog: 0-100mV, 0-5V, 1-5V, 0-10V. 0-20mA, 4-20mA.
- Sampling cycle : 50ms.
- Control output 1 : Current(DC0/4-20mA) or SSR drive(11VDC
) [ON/OFF].
- Option output : Alarm 1, RS485 comm.
- Power supply : 100-240VAC~ 50/60Hz.
- Protection structure : IP65(front panel).
- Display method: 4-digit 7-segment LED.
- Control method: ON/OFF control, P, PI, PD, PIDF, PIDS control.
- Input specification : Thermocouple: K(CA), J(IC), E(CR), T(CC), R(PR), S(PR), N(NN), W(TT) RTD: DPt100Ω, JPt100Ω
- Analog: 1-5VDC , 0-10VDC , DC4-20mA..
- Sampling cycle: 500ms.
- Control output : Relay(250VAC~ 3A).
- Power supply : 100-240VAC~ 50/60Hz.
Temp Control, 1/4 DIN, Zone PID, RS485, 100-240VAC; Fixed Control, 4 Alarm, Current/SSR Drive Out1&2, 1 CT+3 Digital Input,
Read more
Applications
■ Calibration service companies and service industry.
■ Measurement and control laboratories.
■ Pressure tests.
Special features
■ Digital indicator with interchangeable pressure sensors (plug-and-play).
■ Measuring ranges 0 ... 1,000 bar [0 ... 14,500 psi].
■ Type of pressure: Positive and negative overpressure,absolute pressure and differential pressure.
■ Accuracy: 0.2 %, optionally 0.1 % (incl. calibration certificate).
■ Data logger for recording measured values.
Read more
Voltec Engineering Limited
Automation and control products are the focus of VOLTEC ENGINEERING LIMITED. In the area of comprehensive industry solutions for alteration, upgrading, and new construction projects, VOLTEC ENGINEERING LIMITED is a one-stop solution provider.
© 2025 Voltec Engineering Ltd. | Design & Developed by mPair Technologies Ltd.

















