Filter

Showing all 5 resultsSorted by latest

Sort:
Show:
DWYER WATER LEAK DETECTOR SERIES WD3

DWYER WATER LEAK DETECTOR SERIES WD3

By spotting water in drip pans in air handler units, beneath raised floors in data centers, or on floors near sump pumps and drains, the Series WD3 Water Leak Detectors guard equipment against water damage. Once the water has risen to a point where it spans the two conductive strips on the housing's bottom, it is detected. Depending on the model selected, local notice of the alarm situation is provided by audio and visual alerts, and remote indication or control is provided by an internal switch to stop additional water buildup. The Model WD3-BP-D1-A is battery-powered for use in situations where power is not available. Alternatively, the water detector can be powered by either AC or DC supply voltages. By using the provided adjustable mounting bracket, the sensing height can be reduced to as little as 1/32". The mounting bracket can be fastened to any flat surface using either the mounting screws or the connected adhesive strips.
Read more
AECO VIBRATION LEVEL CONTROLS

AECO VIBRATION LEVEL CONTROLS

Electrical data: Connection terminals: 0.14 ÷ 2.5 mm2 (AWG 26 ÷ 14) Cable entry:Cable gland: M20x1.5 with cable sheath diameter 6÷12mm CONDUIT: NPTx½ o NPT3/4 Output activation delay: Rods free → Rods covered: c.a. 1 sec Rods covered → Rods free c.a. 1... 2 sec Detection fuctions FSH/FSL: Settable on the circuit with selector switch Vibration frequency: [Hz] 200 c.a. Over voltage category: II Pollution degree: 2 (inside housing) Operative Conditions: Ambient temperature: [°C] -40 ÷ +60 Process temperature-Tc: [°C] -40 ÷ +150 Ventilation:Ventilation is not required Min. powder density: [g/l] Setting A : c.a. 150 - Setting B : c.a. 30 Features of bulk material: No strong tendency to cake or deposit. Max grain size 8 mm Max. mechanical load: [N] 500 laterally on vibrant rods Max. process pressure: [Bar] 16 Vibration: c.a. 200 Relative humidity: 0 ÷ 100%, suitable for outdoor use Altitude: [m] max 2.000
Read more
CS INSTRUMENTS FA 500-DEW POINT SENSOR

CS INSTRUMENTS FA 500-DEW POINT SENSOR

FA 500 - Dew point sensor with integrated display and alarm relay

  • Dew point sensor FA 500 from -80 to 20°Ctd.
  • For refrigeration, membrane, and desiccant dryers, the FA 500 is the perfect dew point sensor with an integrated display and warning relay.
Read more
CS INSTRUMENTS FA 550 -DEW POINT SENSOR

CS INSTRUMENTS FA 550 -DEW POINT SENSOR

FA 550 - Dew point sensor in robust die-cast aluminum housing ✓Robust dew point sensor for gases and compressed air ✓ The Dew point FA 550 is perfectly suited for measuring dew points outside and reliably does so even in punishing industrial settings. ✓Dew point measurement after adsorption dryers, membrane dryers, or refrigeration dryer in compressed air systems.  
Read more
DUNGS Actuator DriveCP-9302-702

DUNGS Actuator DriveCP-9302-702

The CP-9302-702 electronic actuator drive processes a variable input signal from a controller to provide proportional control of an electric actuator. The CP-930-702 is preset for current input (4 - 20 mA) and has additional wiring for connection to an override switch for applications requiring an external override of the input signal. The CP-9302-702 is equipped with built-in jumpers and adjustable potentiometers, so that the type of input signal, deadband, input span, and start point may be readjusted in the field when necessary.
Read more

Filter Products

Categories